RouterBOARD 133

From Noisebridge
Jump to: navigation, search

See also: Sparky

Contents

[edit] OpenWrt

çİş


[edit] Flashing (kamikaze)

Setup dhcp and tftp on a computer you can connect to via wired ethernet

Download http://wifi.ozo.com/airo/openwrt/firmware/kamikaze/2.6/adm5120/latest/openwrt-adm5120-2.6-vmlinux.elf to /srv/tftp/

sudo dnsmasq -i eth0 --dhcp-range=192.168.1.70,192.168.1.77 --dhcp-boot=openwrt-adm5120-2.6-vmlinux.elf --enable-tftp --tftp-root=/srv/tftp/ -d -u dnsmasq -p0 -K --log-dhcp --bootp-dynamic

Connect the RouterBOARD DB-9 serial to computer, and connect with 115200 8N1

Power up teh board

RouterBOOT booter 2.7

RouterBoard 133

CPU frequency: 175 MHz
  Memory size:  32 MB

Press any key within 2 seconds to enter setup

Press any key within 2 seconds

RouterBOOT-2.7
What do you want to configure?
   d - boot delay
   k - boot key
   s - serial console
   o - boot device
   u - cpu mode
   r - reset configuration
   e - format nand
   g - upgrade firmware
   i - board info
   p - boot protocol
   t - do memory testing
   x - exit setup
your choice: 

[edit] Configure boot

Press 'o' then '1' to set boot device to ethernet one time.

Press 'p' then '2' to use dhcp protocol.

[edit] Erase NAND

Press 'e' to erase/format nand memory. This will clear anything previously installed.

Type 'yes' enter, wait...

Press 'x', wait...

[edit] Install OpenWrt

BusyBox v1.8.2 (2008-05-30 09:59:52 EEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 KAMIKAZE (bleeding edge, r11293) -------------------
  * 10 oz Vodka       Shake well with ice and strain
  * 10 oz Triple sec  mixture into 10 shot glasses.
  * 10 oz lime juice  Salute!
 ---------------------------------------------------
root@OpenWrt:/#

Teh SECRET sauce

mount /dev/mtdblock2 /mnt; cd /mnt

wget http://yourserver/kernel

cd /; umount /mnt; mount /dev/mtdblock3 /mnt; cd /mnt

wget http://yourserver/openwrt-adm5120-2.6-rootfs.tgz

gzip -d openwrt-adm5120-2.6-rootfs.tgz; tar xvf openwrt-adm5120-2.6-rootfs.tar; rm openwrt-adm5120-2.6-rootfs.tar; cd /; umount /mnt; sync; reboot

[edit] Downloads

[edit] References

[edit] Meraki Flashed Versions

Manual: http://www.routerboard.sk/files/pdf/rb133&133c_manual.pdf

Note: The following references boards that have a meraki flashed NAND.


[edit] power

The board has a non-standard PoE option, there is also a barrel connector that supports 9-28V DC tip positive supply


[edit] www

Connecting the first ethernet port (has PoE sticker) to a DHCP enabled network will allow access to some meraki web pages. Browse to the IP to see these pages.

  • index.cgi
  • advanced.html
  • configure/index.cgi

Some pages are password protected. The username is 'admin' and the password is the serial number. The serial number can be obtained via the serial terminal using 'cat /MERAKI_SERIAL'


[edit] serial boot output

CuteCom was used to get the following via Serial Console http://cutecom.sourceforge.net/

BusyBox v1.1.0 (2007.09.21-01:28+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

http://meraki.com/

Welcome to your Meraki device.  Please look for developer information at
http://meraki.com.  We would like to encourage you to play with this
platform and add your own features to it.  However, our lawyers
require us to tell you that much of the software on this device is
protected by copyrights, and may not be redistributed or sold.

Like hacking on wireless stuff?  Come work with us!  jobs@meraki.com

Happy Hacking!
00:18:0A:00:F0:DC:/# help

Built-in commands:
-------------------
\0x09. : alias bg break cd chdir command continue eval exec exit export
\0x09false fg getopts hash help jobs kill let local pwd read readonly
\0x09return set shift times trap true type ulimit umask unalias unset
\0x09wait

reboot command, followed by any key to enter setup


00:18:0A:00:F0:DC:/# reboot
00:18:0A:00:F0:DC:/# adm5120_wdt_release: release

The system is going down NOW !!

Sending SIGTERM to all processes.

Sending SIGKILL to all processes.

Please stand by while rebooting the system.
Restarting s\0xf9

RouterBOOT booter 2.7

RouterBoard 133

CPU frequency: 175 MHz
  Memory size:  32 MB

Press any key within 2 seconds to enter setup.

RouterBOOT-2.7
What do you want to configure?
   d - boot delay
   k - boot key
   s - serial console
   o - boot device
   u - cpu mode
   r - reset configuration
   e - format nand
   g - upgrade firmware
   i - board info
   p - boot protocol
   t - do memory testing
   x - exit setup
your choice: 


[edit] more console out

RouterBOOT booter 2.7

RouterBoard 133

CPU frequency: 175 MHz
  Memory size:  32 MB

Press any key within 2 seconds to enter setup..
loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
mem_detect: disable buffers for both banks
mem_detect: checking for 64MB chip in 1st bank
mem_detect: write 0xAAAAAAAA to 0xA0000000
mem_detect: delay 10000 ns
mem_detect: pattern at 0xA1000000 is 0x55555555
mem_detect: write 0xAAAAAAAA to 0xA0000000
mem_detect: delay 10000 ns
mem_detect: pattern at 0xA2000000 is 0x55555555
mem_detect: chip size in 1st bank is 64MB
mem_detect: enable buffers for both banks
mem_detect: 1x64MB memory found
<6>ADM5120 revision 8, running at 175MHz
<6>Boot loader is: RouterBOOT
<6>Booted from   : NAND flash
<6>Board is      : RouterBOARD 133
<6>Memory size   : 32MB
done meminit
Linux version 2.6.16.16 (xyu@xyu-dev) (gcc version 3.4.6 (OpenWrt-2.0)) #14 Wed Sep 26 18:49:21 PDT 2007
ADM5120 board setup
CPU revision is: 0001800b
Determined physical RAM map:
 memory: 013d1000 @ 00c2f000 (usable)
Built 1 zonelists
Kernel command line: console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2 init=/etc/preinit
Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 4096 bytes)
Using 87.500 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 19960k/20292k available (2336k kernel code, 316k reserved, 447k data, 9544k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
unpacking initramfs....done
NET: Registered protocol family 16
adm5120: system has PCI BIOS
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Algorithmics/MIPS FPU Emulator v1.5
PCI: slot number 0 is not supported
PCI: mapping irq for 0000:00:02.0 pin:1, irq:15
yaffs Sep 20 2007 18:44:25 Installing. 
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
watchdog hb: 90  WDOG0: 0xa32806dd  WDOG1: 0x7fff06de
adm5120_wdt_init using heartbeat 90 s cycles 9000
watchdog hb: 90  WDOG0: 0xa3280000  WDOG1: 0x7fff0000
ttyS0 at I/O 0x12600000 (irq = 9) is a ADM5120
ttyS1 at I/O 0x12800000 (irq = 10) is a ADM5120
eth0: ADM5120 switch port0
eth1: ADM5120 switch port1
eth2: ADM5120 switch port2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
RB1xx nand
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 4 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00400000 : "/bootpart"
0x00400000-0x00800000 : "/storage"
0x00800000-0x00810000 : "paniclog"
0x00810000-0x04000000 : "extra"
usbmon: debugfs is not available
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
ip_conntrack version 2.4 (256 buckets, 2048 max) - 232 bytes per conntrack
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Freeing unused kernel memory: 9544k freed
init started:  BusyBox v1.1.0 (2007.09.21-01:28+0000) multi-call binary

Please press Enter to activate this console. yaffs: dev is 32505856 name is "mtdblock0"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.0, "mtdblock0"
yaffs: auto selecting yaffs1
yaffs: dev is 32505857 name is "mtdblock1"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.1, "mtdblock1"
yaffs: auto selecting yaffs1
adm5120_wdt: starting watchdog w/timeout 90 seconds
watchdog hb: 90  WDOG0: 0xa328028c  WDOG1: 0x7fff028c
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413, REGOPS_FUNC)
wlan: 0.8.4.2 (svn 10828)
ath_rate_sample: 1.2 (svn 10828)
ath_pci: 0.9.4.5 (svn 10828)
PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 10.4 phy 6.1 radio 6.3
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
couldn't load module 'wlan_scan_sta' (-89)
unable to load wlan_scan_sta
wifi0: Atheros 5212: mem=0x11400000, irq=15
click: starting router thread pid 478 (818d3480)
wlan: mac acl policy registered

!!!!! reading /tmp/mtunnel_state failed: No such file or directory
couldn't load module 'wlan_scan_monitor' (-89)
unable to load wlan_scan_monitor



BusyBox v1.1.0 (2007.09.21-01:28+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

http://meraki.com/

Welcome to your Meraki device.  Please look for developer information at
http://meraki.com.  We would like to encourage you to play with this
platform and add your own features to it.  However, our lawyers
require us to tell you that much of the software on this device is
protected by copyrights, and may not be redistributed or sold.

Like hacking on wireless stuff?  Come work with us!  jobs@meraki.com

Happy Hacking!
00:18:0A:00:F1:7C:/# 



Wiki page for RB133 http://wiki.openwrt.org/doku.php?id=oldwiki:openwrtdocs:hardware:mikrotik:rb100

Personal tools